What is the size of the tool?

The overall length of the brad pusher is 6-3/4-Inch and the handle length is 4-Inch.

What is the brad pusher made of?

The brad pusher is made of brass and has a beechwood handle with a brass ferrule.

What type of pins can be used with this brad pusher?

You can use wire brads with this brad pusher to be driven home into frames or small moldings.

What is the largest diameter nail head that will fit?

The largest diameter nail head that will fit is not specified, but a 9/64th bit slides in but does rub the sides a bit. 1/8th goes in easily.

Is this product magnetized or not?

Yes, the product is magnetized.

Will this tool be able to use 18 gauge brad nails?

Yes, this tool can use 18 gauge brad nails. You may need to drill a pilot hole depending on the type of material and how deep you want to insert the brad but the device will hold it for you and let you get the brad started.

Is the shaft for this tool supposed to be rather loose/floppy where it slides up into the handle?

Yes, the shaft is supposed to be loose to where one might think it needed to be screwed or tighten but that the way it should be so that as your putting pressure on the brads they move with ease.

Will this accept small standard finish nails in US?

The tool was designed for wire brads, but it works terrific with small briad type nails. It may work well with 3&4 penny nails also.

Can I install quarter round using this?

The diameter of the device is approximately 1/8 inch and it was designed for wire brads, so it may not work for installing quarter round.

How small of a brad nail will it hold?

The device is a little big for smaller nails, but it does work for pushing pin nails into model boat planking. You can buy smaller pushers for smaller nails.

Can it be used to drive the small nails for model railroad track?

The tool is a little too big for driving nails for tracks. You can get one that is smaller in diameter and would work a lot better for track nails (pins).

Will it actually drive the brad itself with the spring or is it just a manual pusher?

It is not automatic, so it must be driven manually to push the brad. A small tap of a hammer can be used when the nail is within about 1/8 inch from the surface of the wood to actually set the nail below the surface. It is important to tap the brad pusher gently to set the nail because hitting the brad pusher with the hammer too hard may leave an impression in the wood.

Explore

Shop By Category

Added to Cart

Your shopping cart is emptyLets Change that !Continue Shopping

https://m.media-amazon.com/images/I/51C3K3PrG6L._AC_SL1000_.jpg

KREG

Crown Tools 110XW Big Horn 20108 Rampin Brad Pusher

Item #:1723897

4.7 rating

Write a review

PKR 12156

This product is not Fulfilled by Ubuy and can take minimum 10 days in delivery. We might cancel the product from the order and refund you if any issue arise with the delivery of this product.

Availability : In Stock

Quantity :

Note: Step Down Voltage Transformer required for using electronics products of US store (110-120.). Recommended power converters Buy Now.

Our Top Logistics Partners

Quality spring-loaded Brad pusher with magnetic ram to drive pins without marking the workpiece

Product Details

Package Weight

Features & Benefits

Made from brass and beechwood
Overall length of 6 3/4-Inch
Features a magnetic spring loaded ram
Useful to hold and drive wire brads into frames or small moldings
Exceptional quality tools from Crown Hand Tools Ltd, Sheffield, England
Beechwood Handle with Brass Ferrule

Product Description

Crown Tools 110XW Big Horn 20108 Rampin Brad Pusher

Overview

Have any Query?Chat with us

Customer Questions & Answers

Question : What is the size of the tool?
Answer : The overall length of the brad pusher is 6-3/4-Inch and the handle length is 4-Inch.
Question : What is the brad pusher made of?
Answer : The brad pusher is made of brass and has a beechwood handle with a brass ferrule.
Question : What type of pins can be used with this brad pusher?
Answer : You can use wire brads with this brad pusher to be driven home into frames or small moldings.
Question : What is the largest diameter nail head that will fit?
Answer : The largest diameter nail head that will fit is not specified, but a 9/64th bit slides in but does rub the sides a bit. 1/8th goes in easily.
Question : Is this product magnetized or not?
Answer : Yes, the product is magnetized.
Question : Will this tool be able to use 18 gauge brad nails?
Answer : Yes, this tool can use 18 gauge brad nails. You may need to drill a pilot hole depending on the type of material and how deep you want to insert the brad but the device will hold it for you and let you get the brad started.
Question : Is the shaft for this tool supposed to be rather loose/floppy where it slides up into the handle?
Answer : Yes, the shaft is supposed to be loose to where one might think it needed to be screwed or tighten but that the way it should be so that as your putting pressure on the brads they move with ease.
Question : Will this accept small standard finish nails in US?
Answer : The tool was designed for wire brads, but it works terrific with small briad type nails. It may work well with 3&4 penny nails also.
Question : Can I install quarter round using this?
Answer : The diameter of the device is approximately 1/8 inch and it was designed for wire brads, so it may not work for installing quarter round.
Question : How small of a brad nail will it hold?
Answer : The device is a little big for smaller nails, but it does work for pushing pin nails into model boat planking. You can buy smaller pushers for smaller nails.
Question : Can it be used to drive the small nails for model railroad track?
Answer : The tool is a little too big for driving nails for tracks. You can get one that is smaller in diameter and would work a lot better for track nails (pins).
Question : Will it actually drive the brad itself with the spring or is it just a manual pusher?
Answer : It is not automatic, so it must be driven manually to push the brad. A small tap of a hammer can be used when the nail is within about 1/8 inch from the surface of the wood to actually set the nail below the surface. It is important to tap the brad pusher gently to set the nail because hitting the brad pusher with the hammer too hard may leave an impression in the wood.

Customer Ratings

4.7 out of 5

197 customers ratings

5 star
79%
4 star
11%
3 star
7%
2 star
2%
1 star
1%

Review this product

Share your thoughts with other customers

Crown Tools 110XW Big Horn 20108 Rampin Brad Pusher

The Crown Tools 110XW / Big Horn 20108 Rampin Brad Pusher is a high-quality and well-built tool for pushing brads. It is worth the extra cost compared to cheaper alternatives. The tool is easy to use and provides better control compared to using a hammer. However, it may require a pilot hole when working with hardwoods. It cannot be used for installing quarter round or driving nails for model railroad tracks. Overall, this brad pusher is recommended for its durability, functionality, and precise application.

Pros

High-quality and well-built
Easy to use
Better control than using a hammer
Durable and functional
Precise application

Cons

May require a pilot hole for hardwoods
Not suitable for installing quarter round
Too big for driving nails for model railroad tracks

Important Information

Limitations : For products shipped internationally, please note that any manufacturer warranty may not be valid; manufacturer service options may not be available; product manuals, instructions, and safety warnings may not be in destination country languages; the products (and accompanying materials) may not be designed in accordance with destination country standards, specifications, and labeling requirements; and the products may not conform to destination country voltage and other electrical standards (requiring use of an adapter or converter if appropriate). The recipient is responsible for assuring that the product can be lawfully imported to the destination country. When ordering from Ubuy or its affiliates, the recipient is the importer of record and must comply with all laws and regulations of the destination country.
Not all the products listed on Ubuy are for sale, as Ubuy is a global search engine. Products are subject to export/trade regulations.

Crown Tools 110XW Big Horn 20108 Rampin Brad Pusher

View Cart & Checkout